Coats 70X-AH-1 Tire Changer & Coats 950 Balancer rebuilt with warranty






Built to Make Changing Low Profiles, Run flats, and other Tough Tires Fast and Easy



All machines include a 1 Year Parts Warranty


 With Full Technical Support



What Makes Us Different Is Our Process


Our Machines Are More Than A Quick Paint Job


True Rebuilds Require The Following



  • Completely remanufactured by our qualified trained technicians.
  • Each machine is completely disassembled down to the frame.
  • Each Frame is stripped, primed and refinished with industrial grade primer and enamel.
  • Swing Arm to Column Bushings are replaced.
  • Robo Arm® Assembly Completely Rebuilt with NEW Seals - Actuator Valve - Hard Lines - Gauge Assembly.
  •  Transmission Disassembled
  • All components cleaned - NEW Seals - O rings - Bearings are replaced.
  • Gears are checked and replaced as needed to meet original factory specs.
  •  Transmission case refilled with NEW oil and checked for proper operation.
  •  All EH and EF Models come with NEW Turntable Drive Motor - Wiring Harness - Forward Reverse Switch.
  • All Air Motors are disassembled - Cleaned - NEW Vanes - Bearings - Seals replaced and refinished.
  • One-way Flow Valves Reassembled - Torque and PSI settings tested to original factory specs.
  • 4-way Valves replaced with NEW to provide function of the Table Rotation - Bead Breaker System - Table Clamp Movement.
  • Table disassembled - all moving parts readjusted and lubricated. We reset Carriers and Jaws.
  • Table - Bead Breaker - B/L Cylinder are cleaned and refinished. Plungers and Seals replaced.
  • Replace Cylinder Sleeve as needed. We reassemble and test to factory PSI settings.
  • Replaced with all NEW Hoses - Hard Lines – Bolts -  Bead Breaker Button - Actuator Valve - Machine Oil - Regulator - Tire Inflator Whip Hose - Bottle and Brush.
  • Gripmax Table clamps are to Factory Specs.
  • NEW Removable plastic covers for protecting Rims on each clamp.
  • Gauges tested and replaced with new as needed.
  • Pressure Limiter Assembly disassembled and all O Rings and Diaphragms Replaced.
  • Pedal Assembly disassembled, cleaned, checked for wear, adjusted and refinished.
  • After the Tire Changer has been reassembled it is tested thoroughly by changing tires multiple times to ensure proper functioning.
  • Complete PDF copies of the Operator and Spare Parts manuals come with each machine
  • The machine is then stretch wrapped and banded to a pallet with steel strapping for safe shipping worldwide.
  • All Machines Come with a 1 Year Parts Warranty with full Technical Support.
 Diameter 6" - 22" External; 8" - 24" Internal

13-28" External (with optional extender clamps - available for additional cost)
Rim Width 14" Maximum
Tire Diameter 50" Maximum
Drive System Air 
Air Source (Air) 150 to 175 PSI, 5 HP compressor, 14 to 15 SCFM @ 150 PSI
Storage 70X: On Chassis
Bead Loosening 70X: Handle Actuated
Chassis Footprint 49"W x 48"D x 76"H
Shipping Weight 700 lbs.




A High Volume Solution


What Makes Us Different Is Our Process


Our Machines Are More Than A Quick Paint Job

True Rebuilds Require The Following





·        Balancer is completely disassembled down to the Frame.

·        Frame is stripped, primed and repainted with original factory paint.

·        Direct Drive Motor is load tested - bearings checked and cleaned thoroughly.

·        Encoder is cleaned and checked for proper function and replaced with NEW one if needed.

·        Cooling Fan is cleaned and tested.

·        PCB Board is taken off the Control Panel and cleaned and tested with factory diagnostic equipment to meet load ratings, and replaced as needed with NEW.

·        Control Panel is cleaned and tested with Factory Diagnostic Equipment specific to this panel, and replaced as needed with NEW.

·        Motor Control Boards tested with Diagnostic Equipment, and replaced as needed with NEW.

·        Limit Switches are tested and replaced with NEW ones if needed.

·        ALL  Plastic Trim – Hood – Tray – Shroud on Motor – Cone Holder – Screen Holder are cleaned and refinished.

·        Each Cone Set and Hub Nut that comes with the Balancer is sand blasted clean and checked for defects. Then tested to ensure they fit Balancer Shaft for accurate balancing.

·        Each hub nut shaft is cleaned and relubricated.

·        After the Balancer is reassembled it is recalibrated and tested a minimum of 50 times with various size rims and tires to ensure the Motor Mount Piezos are reading true and  the overall performance of the Balancer is ready for service.

·        Complete PDF copies of the Operator and Spare Parts Manuals come with each machine.

·        The Balancer is then stretch wrapped and banded to a pallet with steel strapping for safe shipping worldwide.





Balancers include a parts warranty

1 Year On Drive Motor and 90 Days On Remaining Major Components

With Full Technical Support


Key Features:

  • 1 1/2 horsepower direct-drive motor and 16-bit microprocessor provide super-fast five second cycle times.
  • Eight separate balancing modes (static and dynamic modes, RV and four different alloy modes, plus match mount).
  • Convenient keypad entry
  • Keyboard activated "hood start" saves time.
  • Ounce/gram conversion and a roundoff feature eliminates complicated calculations.
  • 25-pocket weight tray provides abundant storage.
  • Self calibration.



Balancing Modes
Tire Diameter Up to 40"
Rim Width 2" to 19.9"
Max. Tire Wt. 150 lbs.
Shaft Diameter 1-1/8" or 40mm
Shaft Length 6-5/8"
Resolution: Oz. 0.01
Resolution: Degrees 1.4
Accuracy: Oz. 0.01
Power Requirement 220v AC, 1-3 Phase
Footprint 57"W x 50"D
Shipping Weight 586 lbs.







BUY NOW: $7298.00


-- $399.00 SHIPPING --




Shipping costs includes delivery of your order to a business address 
with a dock or other way to load or unload truck 

Liftgate, Residential, and Limited Access Delivery require additional costs if needed for shipment.







Yes we ship International
Additional shipping cost applies - Call for Quote


Please visit our store for more tire maintenance equipment

Seller reserves the right to withdraw item from auction at anytime due to prior sale.

IES sells Quality remanufactured products

· The contents of this listing refers to remanufactured products and/or equipment.
· IES takes pride in the extensive rebuilding efforts its trained technicians provide for every
piece of equipment sold.
· Each product listing details the remanufacturing process IES uses for each product it
· The products sold on our Website have not been endorsed by or approved by the original
manufacturer and the products do not fall under the original manufacturer's warranty.
· Where indicated, IES provides buyer protection for a parts warranty and full technical


COATS®, ROBO-ARM®, RIM CLAMP®, GRIP-MAX®, and other trademarks are registered trademarks owned by Hennessy Industries, Inc